advertisement

How to Fastening zipper?

How to Fastening zipper?

Zip fastenings

Most skirts, and many dresses, fasten with a zip and, if this is inserted badly, it can easily spoil the finished look of an otherwise excellent garment. Zips are usually inserted into an opening in a seam, and they can be centred behind the seamline or set to one side. The latter method is more suited to skirts and close- fitting garments and is slightly easier to do However, the symmetrical stitching of the centred zip makes it well-suited to centre front and centre back positions. Wherever the zip is to be placed, correct preparation of the opening is important. Sew the seam that the zip is to be inserted into, leaving an opening that is slightly longer than the zip. Remember to fasten off securely at what will be the base of the opening. Now baste the remaining section of the seam closed, exactly along the seamline. Neaten the seam and press it open, taking care not to stretch the basted section.

Insert the zip using one of the methods shown on these pages. Use the’zipper foot on your sewing machine – it can be moved from side to side, depending upon which side the zip teeth are on when you are stitching. Do not trim off the zip tapes at the bottom of the zip. Once complete, carefully press the zip opening, taking care not to create indentations of the zip teeth on the right side of the garment. A centred zip has two lines of stitching which are equal distances from the actual opening edge. The zip teeth lie directly under the opening edge.

advertisement

With a lapped zip. There is really only one visible line of stitching and the zip teeth are centred between this stitching line and the pressed edge of the zip opening. The two lines of stitching that hold the zip in place are done separately and should be stitched in the same direction either from top to bottom or vice-versa.

Inserting a Lapped Zip

  1. Remove the basting that holds the zip opening closed. Place the zip under the righthand edge of the opening so the pressed edge lies next to the zip teeth; the zip stop should be positioned just above the base of the opening. Pin and baste the zip in place along this edge. Stitching from the right side, with the zipper foot attachment on the machine, stitch this side of the zip in place, as close as possible to the zip opening edge. Fasten off securely.
  2. Now bring the other edge of the zip opening over the zip so that this free pressed edge just covers the first line of stitching. Pin and baste the zip into position along the lefthand edge. Now stitch this side of the zip in place, stitching 1-1.2cm (3/8-1/2in) from the pressed edge. Remember to stitch across the base of the opening to the seamline.

Inserting a Lapped Zip

Inserting a Centred Zip

  1. With the zip opening still basted closed, lay the closed zip against the wrong side of the fabric. The zip teeth should be directly over the basted seam and the zip stop at the lower edge just above the end of the machine stitching. The slider of the closed zip should be about 2.5cm (1 in) from the top of the opening. Insert the pins at right angles to the zip. Now, working from the right side, baste the zip in place, working two parallel lines, one down each side of the zip to serve as stitching guidelines.
  2. From the right side, and using a zipper foot attachment on your machine, stitch the zip in place. Start at the top of the lefthand edge and stitch 6-8mm (1/4-3/8 in) away from the basted seamline. At the base of the opening, just below the zip stop, stop stitching with the needle in the fabric, raise the machine foot and swing the fabric so that you can stitch across the base of the opening. Now swing the fabric again and complete the zip insertion by stitching along the righthand edge of the opening, stitching the same distance away from the basted seamline as before. Remove basting.

Buttonholes and Buttons

Buttonholes should be marked very carefully and stitched accurately. If a buttonhole is placed on a band, it should run parallel to the longer edges of the band, not across it. And the button it will fasten over – should also be placed centrally across the band.

Many sewing machine manuals will tell you the best way to sew a buttonhole using that particular machine. A buttonhole is basically two rows of very short, narrow zigzag stitches worked next to each other, with wider zigzag stitches worked across each end. To achieve a buttonhole that is really even, loosen the tension of the top thread slightly so that the stitches interlock just to the wrong side of the work, leaving the right side neat.

A buttonhole should be slightly longer than the button that is to pass through it. About 1-2mm (1/24-1/12 in) longer is sufficient, unless you are using a very thick button, where it may need to be slightly longer still. Take great care when cutting the buttonhole that you do not accidentally cut through the stitching. The two rows of stitching forming the sides of the buttonhole should be just far enough apart to allow you to cut between them. Use small, very sharp scissors to cut the buttonhole after it has been sewn. Stop cutting just before you get to the end stitches.

When a button is attached it should stand just above the surface of the garment. That way, once the garment is buttoned, the button will lie flat against this second section without distorting it.

Hooks and eyes

Hooks and eyes are often used to fasten waistband and neck edges. Those with loop-shaped eyes are used where there is no overlap, and those with bar- shaped eyes where there is an overlap. The hook and eye are sewn on by hand using a double-thread Position the hook on the wrong side with the end even with the garment edge.

A loop-shaped eye is positioned on the wrong side of the garment, opposite the hook, with the end protruding beyond the garment edge just enough to allow it to be fastened. A bar-shaped eye is sewn to the right side of the underlap.

advertisement

Making A ButtonHole

  • To make a buttonhole, start by working the first side forwards, then work one end set of stitches. Next, the second side is usually worked in reverse, ending with the second set of wider stitches. If your machine will not work the reverse stitches as evenly as the first side, then work this side forwards as well by turning the work at the first end of the buttonhole.

Attaching A Button

  • Start by sewing on the button using a double thickness of sewing thread and leaving all the stitches slightly loose. You may find it easier to do this if you slip a matchstick between the button and the fabric. Once the button is attached, wind the remaining thread tightly around the shank of threads created. Work one or two stitches through this shank and cut off the thread.
Note: For this article, "how to fasten a zip without a zipper" terms have been used in searchs..
Look at the other similar posts:

Tags: , ,

Category: Hobbies and Crafts

Share This Page With Your Friends, Easily:

banner